Scott Stone uses EBC Brakes components on his Yamaha R1
Retford-based Scott Stone is competing in No Limits Racing’s Pirelli Super Series 1000 Power Trophy on his Yamaha R1, aiming to achieve solid results throughout the year.
Stone relies on EBC Brakes’ GPFAX (front axle) and Double-H Sintered (rear axle) brake pads to help giving him a fighting chance of achieving some of the fastest lap times on the grid.
Following multiple podiums in 2025’s Premier 1000cc Championship, we caught up with Stone following the first 2026 round at Norfolk’s Snetterton Circuit
Test Days
“We had two test days for the first round which was good to give us extra time to get up to speed. I was happy on Day 1, but struggled with tyre wear and grip on Day 2 when the temperature dropped. I was a little worried on what my qualifying time might be after an average couple of days on the bike, so a quick call to Not So Fast was what I needed just to set the plan.”
Qualifying
“Bike felt great and on Lap 3 I managed 1:56.7, so pulled in to save tyre. This put me P6 in class taking the three BSB lads out of the numbers and, basically, leading my bunch. So, yes, happy. Best lap: 1:56.706 and 10th on grid.”
Race 1
“Didn’t get a great start and found myself in a close four-way battle for most of the race, which was fun. Had to make up some early ground to get there. Saw parts of the track where I could improve and was looking forward to a strong Race 2. Best lap: 1:56.340 and 10th in Class.”
Race 2
“Got a much better start, settled in and led the bunch (in P9) until Lap 5 when I started to drop back. I was running in the mid to low 56’s and knew I needed to drop into the 54/55’s to hold position. I wasn’t sure if the bike started to turn slower or I may have tried too hard to pull away, but it started to feel hard work. This was the hardest part of the weekend to accept as, with clear track ahead, I gave myself the opportunity to pull away, but wasn’t able to. I then got caught in an incident which put me on the grass and I lost the chance to hold onto the group. Brought it home P9 in Class with a slightly better lap time of 1:56.298.”
Race 3
“Made a few slight changes to the bike for Race 3, keen to run at the pace I felt possible if I could get to the front of the pack and find clear track. Another good start and made up some early places. However, a rider around me had multiple bike problems making it difficult and risky to pass. I had to take avoiding action, then trying to get away from the problem, made a mistake and ran on at the next hairpin, losing 5 places. Frustrated, I got back on track and recovered as many places as possible in the remaining laps. I managed to make my way back to P12 in Class. Lap 2 was my fastest lap of the weekend and, being 0.4 seconds below my PB set last year, it was a massive disappointment not to improve on that. Best lap: 1:55.973 and P12 in Class.
“In summary, I don’t think the feel I got from the bike was great, although I may have tried to override to compensate. We all know that does not work. I can be faster when things are right. It wasn’t all bad and there were lots of positives to take away from the meeting. Whilst my final placings don’t look spectacular, the 3 podium places were taken by the Tag Honda BSB riders in each race. Allowing for them, my places weren’t too shabby.
“Thank you to No Limits Racing and the marshals for a well very run meeting and a massive well done on the new YouTube channel. A great addition to club level racing.
“Thank you to every single person and sponsor that makes this possible.”
Photos by Matt Sayle Photography
GPFAX Pads
EBC’s GPFAX Sintered Race Brake Pads are for RACE ONLY use. This is a blend of brake pad that has higher friction and far better grip than any other brake product on the market.
Double-H Sintered Pads
ECE R90 brake safety-approved and TUV tested, these ultra-high friction HH rated brake pads remain a market leader for road-going motorcycle brake pads.
